ELECTRAGUARD ESD EPOXY SPECIFICATIONS

Mission Critical Conductive Floor Paint

Click Here for this document in a PDF format

Made in the U.S.A.PRODUCT HISTORY AND OVERVIEW: ElectraGuard was originally invented for use in DOD munitions applications in 1992. Over the years it has been further refined with patented advancements in structural integrity. ElectraGuard is exclusive to United SCP and a proven performer at a realistic price. ElectraGuard is a two part epoxy. Unlike mere latex or one part epoxy floor paints that may last a year or two the ElectraGuard System provides outstanding longevity (many clients report a 10 year service life and the product may easily be recoated if ever needed). The system is well suited for application on a variety of substrates including concrete, wood, well bonded standard vinyl tiles and more.

The ElectraGuard ESD Epoxy Floor Paint System meets or exceeds the latest most stringent standards of electrical conductivity and Tribocharge reduction. Leave "as is" for low glare matte finish or top coat with ElectraThane and or ElectraGlaze for a diamond like shine and ultimate wear resistance.

PHYSICAL PROPERTIES:

Gloss Unsealed: Matte Finish

Gloss Sealed: 88 Min ASTM D1455-82

Colors: Light Gray, Medium Gray, Black Ice, Beige, Emerald Green, Sky Blue

Slip Resistance per ASTM-D2047-5: 0.62 minimum (excellent)

Hardness: Shore 68

Viscosity: 400 to 600

Solvent: Alcohol, water-glycol ether

Flash point: >212 deg. F

Freeze / Thaw Stability: 0 - Do not freeze

Dry time at standard air flow: 8 hours (dry to the touch). Open for traffic in 12

Typical Coverage: 350 to square feet per gallon per coat

Compressive strength over vinyl tiles: Modified ASTM F 9700-00, >2,500

Compressive strength over concrete: DIN1691 equal to or greater than that of the concrete.

Indentation impact resistance per ASTM F1914: DIN EN average of <5%, max 10%

Abrasion resistance per ASTM D1044: SC10F wheel, 550 gm weight, cycles 10k, % loss 1.6

Resistance to wear: DIN EN660-1, M

Film thickness when dry: 1.1 mil per coat

Warranty: Life time electrical properties, 5 years wear (see details for specifics)

Resistance to chemicals: ASTM 925, DIN EN 423, slight change

Resistance to heat: ASTM 1514 ∆<8 average., max, <∆E=2.0

Resistance to light: ASTM 1515 ∆<8 average., max, <∆E=6.0

Fire resistance: DIN 4102, B1

Color fastness: ISO 105 BO2, >6

Critical radiant flux: ASTM E648, NFPA 253, >1.08 w/cm2 (class 1 interior floor finish, NFPA code 101

Shelf Life and Weight: 24 months, unopened at 70 deg F, +/- 10 degrees. Weight: 10 Pounds Per Gallon.

CA Prop 65: Compliant. No warnings

VOC Content: Meets Federal Guidelines at <350 g/l. Zero VOC when cured. NOTE: this product may be supplied in QUARTS. These are EXEMPT from State and Local VOC restrictions nationwide.

Shipping: May be shipped Air Freight. Non Regulated, IEN 99-3A-3B, HTC 3209.90.0000

 

TYPICAL ELECTRICAL PROPERTIES UNSEALED (fully cured)* 

ITEM

STANDARD TEST METHOD

UNSEALED ELECTRAGUARD

Electrical Resistance, Surface to Surface (PTP)

 

ANSI-ESD STM7.1 -2021, EN1081, IEC61349-5-1. Tested @ 100 V / 10 V, 12% / 45% rH, results in ohm

>2.50E04 <1.0E06

Electrical Resistance Surface to Ground (RTG)

>2.5E04 <1.0E06

Electrostatic Propensity

AATCC 134-2001  / EN 1815 result in kV

<.5 PASS

Static Decay

MIL-Std 3010C, Method 4046 at 12% Relative Humidity (formerly FED-STD 101C, Method 4046)

<0.02 sec PASS

Combination resistance of technician, heel grounders and flooring

ANSI ESD S20.20-2021 (prequalification), 97.1

<1.0E09 Ohms. PASS

Tribogeneration

ANSI ESD S20.20-2021, 97.2 (prequalification) / IEC 61340-4-5

Does not exceed 100 volts. PASS 

(typical <10 volts +/- polarity)

Electrical Conductivity, High Velocity Medium and Light Gray

DOD 4145-26-M, (March 13, 2008) tested at 500 Volts, RTG/PTP

> 40 kV and <1 Meg Ohm. PASS

Electrical Conductivity, High Velocity Medium and Light Gray

NFPA 484-2015, tested at 500 Volts, RTG/PTP

> 40 kV and <1 Meg Ohm. PASS

Electrical Conductivity, High Velocity Medium and Light Gray

ASTM F-150, tested at 500 Volts, RTG / PTP

> 40 kV and <1 Meg Ohm. PASS

Electrical Conductivity, High Velocity Black Ice

NFPA 484-2015, tested at 500 Volts, RTG/PTP

> 20 kV and <1 Meg Ohm. PASS

Electrical Resistance, Surface to Surface Resistance to Ground

UL 779

PASS: No locations below 10,000 ohms, average readings > than 25,000 ohms.

 

Note: Resistance values may be easily adjusted upwards with an additional coat of ElectraThane to meet minimum DOD resistance levels for use in 240 volt applications

 

TYPICAL ELECTRICAL PROPERTIES SEALED (fully cured)*

 with 2 thin coats of ElectraThane and 1 thin coat of ElectraGlaze. 

ITEM

STANDARD TEST METHOD

SEALED ELECTRAGUARD

Electrical Resistance, Surface to Surface (PTP)

 

ANSI-ESD STM7.1 -2020, EN1081, IEC61349-5-1. Tested @ 100 V / 10 V, 12% / 45% rH, results in ohm

>2.5E04 <1.0E07

Electrical Resistance Surface to Ground (RTG)

>2.5E04 <1.0E07

Electrostatic Propensity

AATCC 134-2001  / EN 1815 result in kV

<.5 PASS

Combination resistance of technician, heel grounders and flooring

ANSI ESD S20.20-2021(prequalification), 97.1

<1.0E09 Ohms. PASS

Static Decay

MIL-STD 3010C, Method 4046 at 12% Relative Humidity (formerly FED-STD 101C, Method 4046)

< .1 sec

Tribogeneration

ANSI ESD S20.20-2021 (prequalification), 97.2

Does not exceed 100 volts. PASS 

(typical <5 volts +/- polarity)

Electrical Resistance, Surface to Surface Resistance to Ground

UL 779

PASS: No locations below 10,000 ohms, average readings > than 25,000 ohms.

 

* Please Note: The above readings are reflective of three coats applied to concrete and allowed to cure for a 3 week period prior to testing. Highly Insulative or conductive substrates such as ceramic or steel, high humidity (damp) concrete, ambient humidity, grounding techniques and coating thickness may alter your final results. Always pretest the coating to your internal specifications in a small inconspicuous area prior to full scale application. Resistance values may be easily adjusted upwards with additional coats of ElectraThane or ElectraGuard NC (rolled with a 1/4" nap roller). This process will allow the system to fall in the static dissipative range of >1.0E06 and <1.0E09.

 

Typical Charge Generation

Floor Materials and Footwear

Charge Generation of Person in ESD Footwear

Testing per ANSI/ESD STM97.2 Flooring Section

Environmental Conditions: 38.7%rH, 78.9o F (avg.) Areas 1 through 5

Devices used in this Testing: Monroe Charge Plate Analyzer, Oscilloscope, PC

NOTE:  Device output is 1/1,000th the actual charge of the plate

Passing Range for this procedure is less than 100 Volts

 

Maximum Negative Voltage: (-) 4.37     Maximum Positive Voltage: (+) 6.56

Median Absolute Voltage: (+) 1.25     Average Absolute Voltages: (+) 1.17

 

ElectraGuard Tribogeneration per STM97.2

 

Area 1

Area 2

Area 3

Area 4

Area 5

1 to 1,079

1,080 to 2,003

2,004 to 3,081

3,082 to 4,312

4,313 to 4,904

Figure 3, 97.2 Locations by Data Points

 

 

PN: EG-1, EG-CASE, EG-5, ElectraGuard ESD Epoxy Floor Paint

United Static Control Products Inc

Document Number:

SRC10109E

Original release date: 01/16/2003

1st revision date: 04/06/2007

2nd revision date: 06/09/2015

3rd revision date: 01/16/2017

4th revision date: 7/12/2017, PTP & RTG @ 500 volts added

5th revision date: 8/14/19, change table color for ease of print.

6th revision date: 6/12/20, Meets UL Standard 179

7th revision date: 7/12/20, conductivity < 1 meg ohm cured

8th revision date: 2/21/21, added voc content

9th revision date: 3/29/21, new ANSI S2020-2021 standards

 

 

*